Getting Started with Plumber's Essentials When Installing a Bathtub
Getting Started with Plumber's Essentials When Installing a Bathtub
Blog Article
What're your thoughts and feelings on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is easily easily accessible, the task can relocate immediately; if you have to open up a wall to eliminate the old bathtub and place the new bath tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and set in the new one. Ensure you have certified on your own for the work and fit attempting it. As opposed to hiring a professional to take over a halfway-completed task, it is better to take into consideration employing one before you begin. Chances are you may require a professional plumber to make tube links.
This write-up will assist you mount a new tub in your washroom if you have already gotten a brand-new tub as well as don't need to alter the plan of your previous water supply pipes.
Your tools as well as product list should consist of the following:
Getting ready for the Setup
First of all, the supporting structure supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The process of removing the existing taps can be fairly bothersome due to the restricted gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth all set for the staying water that will come from the pipes. As soon as the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the needed setting. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bathtub until the level checks out degree.
To install faucets, fit the bottom of the furthest flexible tap adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the supply of water and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill the bath tub and also examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the tub ought to wait up until the bath tub has been utilized at least once as this will certainly resolve it into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making certain that the washers are in location between the tap as well as the sink. Protect the tap in position with the supplier supplied backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, leading to difficulties with moisture as well as feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealant can split fairly early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our section on How to Install a Bathtub Yourself. Thanks a ton for spending some time to read through our post. Sharing is good. You never know, you might be doing someone a favor. Kudos for your time. Come back soon.
Set An Appointment Report this page